دستگاه Soldering /Desoldering/Hot Air Rework Station سه کاره مدل  FR-702B دارای 4 پورت خروجی  دو عدد هویه- یکعدد قلع کش و یکعدد هویه هوای گرم بهمراه کلیه متعلقات استاندارد قید شده در کاتالوگ شامل یکعدد هویه- قلع کش و هوای گرم با نوک و نازل های استاندارد و پک قطعات یدکی ساخت Hakko ژاپن

4 Port Rework Station with 140 W desoldering gun, M-type soldering iron and 670W hot air

It handles various soldering, desoldering and reworking by choosing proper handpieces from a selection of 7 types.

Other than the standard handpieces of 140 W desoldering gun, M-type soldering iron and high power & large volume hot air, there are 4 more applications. Consumed tip nozzle and heating element can be replaced individually, and running cost is much lower than the composite type.

O p t i o n	Soldering iron L type FX-8805	N2 Soldering iron FX-8802	One-hand Manual-solder-feed iron FX-8803	SMD hot tweezer FX-8804
	T19 series tips	T18 series tips		950/FX-8804 series tips

High-power Desoldering gun FR-4103

Increasing the power to 140 W from 50 W of our previous models (HAKKO 474・475), it can make it easy to desolder on multi-layer PWB which was never an easy job, and it can also shorten the process time.
A wide selection of nozzle, with the addition of new types, is available for a variety of desoldering works.

• Long type nozzles for narrow space
• Oval shape nozzles for flat terminals
• SS type nozzles for micro land-patterns

Soldering iron FX-8801/FX-8805

Thermal conductivity has been increased by reviewing external configuration and internal structure of 900 tip series.
Now T18 and T19 tip series are selectable depend on work environment.

Hot air handpiece

670 W high power and large volume hot air improves work efficiency.

High power and large volume hot air for quick removal of components

New type of nozzles for improvement of temperature characteristics

The new nozzle improves work efficiency with uniform heating by hot air convection inside the nozzle which is created due to vents on the nozzle top. (only with BGA nozzles)

Vacuum pickup function

The vacuum pick up function is to pick up a component with a suction pad and vacuum. It will pick a component only after the hot air melts solder joints. This can avoid an error to peel off the land by removing a component with excessive force.

Pickup indicator lets you know the pickup timing at a glance!

By pre-setting pickup function, a component can be picked up automatically when solder is melted. Then, the indication comes up and the moment of picking up will be visible.
Even a component and solder joints cannot be seen as covered by a nozzle, easy and safe picking up is possible.

N₂ soldering iron FX-8802

The N₂ gas runs into the nozzle assembly and covers over the soldering tip. It prevents the soldering tip and the heater from being readily oxidized and performs great role as a preheating.
Two effects of N₂ system, preventing oxidation or preheating effect, can improve soldering defects such as bridging, protrusion icicle, insufficient solder filling in PTH, etc.
T18 tips series are compatible with this application.

One-hand Manual-solder-feed iron FX-8803

• Solder and feed with one hand
• Feed a set amount of solder with one hand
• Manual feed system is perfect for cellular manufacturing.
• Soldering work can be conducted at the pace of the operator.
• T18 tips series are compatible with this application.

SMD Hot Tweezer FX-8804

• Direct heating—less influence upon surrounding components on crowded boards.
• Easily removes SMD chips and flat packages up to 25mm.
• The collet allows easy replacement and alignment of the tips.